1–15 mm / 0.039–0.591 in Padova Hole Cutter Collection with 18 Cutter Sets and Long-Handle Striking Tool PDVSET0015EL

Padova Hole Cutter Collection with Manual Striking Tool

This professional collection has been assembled for leather, textile, tarpaulin, bag and accessory workshops that regularly require several different hole diameters. It contains 18 complete Padova cutter sets and one long-handle manual striking tool.

The Padova cutters cover 17 different hole diameters between 1 mm / 0.039 in and 15 mm / 0.591 in. Two structurally different 5 mm / 0.197 in Padova models are included as separate products, bringing the cutter quantity to 18 complete sets.

Included Hole Diameters

Complete Collection Contents

Physical Component Count

• 18 Padova cutting tools
• 18 matching lower anvils
• 1 long upper holding rod
• 1 lower tool base

Total physical content: 38 components.

When Should This Collection Be Selected?

• When several hole diameters are required in the same workshop
• For leather, faux leather, fabric and canvas preparation
• For bags, belts, wallets and footwear accessories
• For tarpaulin, awning, tent and technical textile work
• Before installing compatible eyelets, rivets or snap fasteners
• For sample making, repairs and small production runs
• When both metric and imperial hole references are required
• When controlled manual hammer application is preferred

Hole Preparation Is Not Final Installation

The Padova cutter prepares the passage through the material. A setting die secures the eyelet, rivet, snap or other component after the correct opening has been prepared. Hole preparation and final installation are separate operations.

How to Select the Correct Hole Diameter

Do not select a cutter according to the visible cap or flange diameter. Measure the actual tube, post, pin, nail or leg that must pass through the material.

• Measure the component that passes through the material.
• Evaluate the total material thickness and elasticity.
• Allow less tolerance on thick, layered or rigid materials.
• Confirm that the hardware passes through without excessive clearance.
• Complete a sample test before repeated production.

Application Instructions

1. Select the Padova cutter matching the required hole diameter.
2. Confirm that the cutter and lower anvil belong to the same diameter.
3. Place the material securely over the lower anvil.
4. Keep the cutter perpendicular to the working surface.
5. Confirm that the cutter is correctly fitted to the manual tool.
6. Apply a controlled vertical hammer strike.
7. Inspect the prepared opening and material edges.
8. Adjust the impact gradually after testing on sample material.

Connection Compatibility Warning

The products shown in the supplied cart appear to use the connection option described as 1/4 in with an approximately 8 mm / 0.315 in connection diameter. Metric and imperial threads may have similar outside diameters while using different thread pitches and profiles.

Not Included

• Hammer
• Eyelets and washers
• Snap fastener components
• Rivets and posts
• Eyelet, snap fastener or rivet setting dies
• Manual hand press
• Impact, electric or pneumatic machines
• Yellow cutting block or additional cutting support
• Thread converters and connection adapters

Related Products 

• Long-Handle Manual Striking Tool KLP00EL01
• 1 mm / 0.039 in Hole Cutter PDV0010DEL
• 3 mm / 0.118 in Hole Cutter PDV00030DEL
• 3.5 mm / 0.138 in Hole Cutter PDV000035DEL
• 5 mm / 0.197 in Hole Cutter PDV00050DEL
• 5 mm / 0.197 in Padova Hole Cutter KLP0005DEL
• 6 mm / 0.236 in Hole Cutter PDV00060DEL
• 8 mm / 0.315 in Hole Cutter PDV00080DEL
• 9 mm / 0.354 in Hole Cutter PDV00090DEL
• 14 mm / 0.551 in Hole Punching Die PDV000140DEL
• All Hole Cutter Tools and Punching Dies

Frequently Asked Questions

How many Padova cutter sets are included?

The collection contains 18 complete Padova cutter sets covering 17 different hole diameters. Two different 5 mm / 0.197 in models are supplied.

Which hole diameters are included?

The included diameters are 1, 2, 2.5, 3, 3.5, 4, 4.5, 5, 6, 7, 8, 9, 10, 12, 13, 14 and 15 mm / 0.039, 0.079, 0.098, 0.118, 0.138, 0.157, 0.177, 0.197, 0.236, 0.276, 0.315, 0.354, 0.394, 0.472, 0.512, 0.551 and 0.591 in.

Is an 11 mm / 0.433 in cutter included?

It is not included. The collection moves from 10 mm / 0.394 in to 12 mm / 0.472 in.

Why are there two 5 mm / 0.197 in cutters?

The collection contains the PDV00050DEL and KLP0005DEL models. They are separate products and must remain separately listed in the package contents.

Are lower anvils included?

Yes. Each Padova cutter is supplied with its corresponding lower anvil.

Is the long-handle striking tool included?

Yes. One KLP00EL01 long-handle manual striking tool set is included.

Can this collection install eyelets or rivets?

It prepares the required openings only. Final installation requires a separate setting die compatible with the selected eyelet, rivet or snap fastener.

Is a hammer included?

The hammer, press and other application machines are not included.

Can every cutter be fitted to the same tool?

Only cutters with matching connection standards should be used together. The connection diameter, thread pitch and thread profile must be confirmed before use.

Is it suitable for production work?

The cutters may be used with compatible press or machine systems. The long-handle striking tool is primarily suitable for samples, repairs, occasional applications and small production runs.

Content updated: 5 August 2026 — E-Düğme