Wide Flat Brass Eyelet Setting Die for 6.2 mm / 0.24 in Eyelets KLP004DUZ

What Is a Wide Flat Eyelet Setting Die Used For?

This Eyelet Setting Die is used to install wide flat brass eyelets with a 6.2 mm / 0.24 in inner opening. It applies controlled pressure to close the eyelet barrel over the washer, helping the eyelet sit evenly and securely on the application material.

This product performs the final installation stage. It does not cut or prepare the hole in the material. Where a pre-hole is required, use a separate Punching Die selected according to the material thickness, coating, density and the actual eyelet geometry.

Compatible Eyelet Geometry

• Eyelet outer diameter: 13 mm / 0.51 in
• Eyelet inner diameter: 6.2 mm / 0.24 in
• Eyelet barrel height: 5 mm / 0.20 in
• Washer outer diameter: 13 mm / 0.51 in
• Washer inner diameter: 7.5 mm / 0.30 in
• Washer height: 1 mm / 0.04 in

Eyelets with a similar trade number are not automatically compatible. A standard flat brass eyelet with a 5.2 mm / 0.20 in inner opening has a different outer diameter, barrel height and washer geometry. Use this die only with the matching wide flat 6.2 mm / 0.24 in brass eyelet system.

Compatible Eyelet

Use this die with the matching wide flat brass eyelet measuring 6.2 mm / 0.24 in inside diameter, 13 mm / 0.51 in outside diameter and 5 mm / 0.20 in barrel height. Confirm the full eyelet-and-washer geometry before repeat production.

Eyelet Setting Die vs. Punching Die

An Eyelet Setting Die installs the eyelet and washer. A Punching Die prepares the hole in the material when necessary. These two tools perform different tasks and should never be used as substitutes for each other.

Thin textile, soft leather or flexible synthetic leather may not require the same pre-hole preparation as thick tarpaulin, layered leather, coated fabric or rigid board. Test the actual material and eyelet system before production use.

Suitable Applications

• Tarpaulin, awning and protective-cover attachment points
• Tents, camping equipment and outdoor textile products
• Leather bags, pouches, covers and accessory details
• Curtains, decorative textiles and home textile products
• Rope, cord, lacing and tie-down passages
• Labels, banners, technical textiles and repair work

Press and Tool Compatibility

This die can be used with compatible hand-hit tools, manual hand presses, impact presses, electric machines and pneumatic machines when the physical die-holder and machine connections are confirmed.

Metric and inch thread systems should not be treated as interchangeable. Similar outside diameters do not guarantee compatibility because thread pitch and thread profile may differ. Confirm the real connection standard of the die, adaptor and press before use.

Application Order

1. Check the material thickness, structure and number of layers.
2. Confirm that the selected eyelet matches the listed dimensions.
3. Prepare a pre-hole only where the actual application requires it.
4. Insert the eyelet from the front side of the material.
5. Place the matching washer on the reverse side.
6. Apply controlled pressure with the Wide Flat Eyelet Setting Die.
7. Check that the barrel closes evenly over the washer and the eyelet does not rotate.

Before Ordering

• This is an Eyelet Setting Die, not a Punching Die.
• Use only with compatible wide flat brass eyelets with a 6.2 mm / 0.24 in inner diameter.
• Confirm 13 mm / 0.51 in outer diameter, 5 mm / 0.20 in barrel height and washer geometry together.
• Do not use it with standard 5.2 mm / 0.20 in inner-diameter flat eyelets.
• Test thick, coated, multilayer or rigid materials before production.
• Eyelets, washers, hand tools, presses, adaptors and Punching Dies are separate products unless explicitly included.

Frequently Asked Questions

Which eyelets does this setting die install?

It is intended for compatible wide flat brass eyelets with a 6.2 mm / 0.24 in inner diameter, 13 mm / 0.51 in outer diameter and 5 mm / 0.20 in barrel height.

Can it install standard 5.2 mm flat brass eyelets?

No. The standard 5.2 mm eyelet system has different geometry. The inner opening, outer diameter, barrel height and washer structure must match the die.

Does this die punch the material?

No. It is an Eyelet Setting Die. Use a separate Punching Die when a pre-hole is required.

Can it be used with a manual hand press?

Yes, when the die connection and press connection are physically compatible.

Is it suitable for tarpaulin and awning work?

Yes, when used with the matching eyelet system, suitable material preparation and the correct press setup.

Are the eyelets and washer included?

No. The matching eyelets, washers, press and other application equipment should be selected separately unless explicitly included in the order.