Suzan Pin Setting Die for 4 mm / 0.16 in Inner Diameter Pins KLP0026Pim

Suzan Pin Setting Die for 4 mm Inner Diameter Pins

This Suzan Pin Setting Die is designed for controlled installation of compatible sheet metal Suzan Pins with a 4 mm / 0.16 in inner diameter and a 6.5 mm / 0.26 in barrel height. It helps apply centred pressure during mounting on leather goods, handbags, wallets, belts, card holders, organisers and textile accessories.

This product is a setting die only. It does not punch holes, cut slots or install a pin by itself without compatible press equipment. Its function is to support the correct setting pressure for the matched Suzan Pin system.

Compatible Suzan Pin System

The die is intended for the compatible sheet metal Suzan Pin system with a 4 mm / 0.16 in finished inner diameter and a 6.5 mm / 0.26 in barrel height. The inner diameter alone does not confirm compatibility.

Check the complete pin geometry before production: barrel form, barrel height, visible cap shape, reverse-side closure, material thickness and the setting surfaces of the die must work together.

Use the matching Sheet Metal Suzan Pin with the corrected 4 mm / 0.16 in inner-diameter and 6.5 mm / 0.26 in barrel-height specification.

Setting Die and Hole Cutter Have Different Roles

• Suzan Pin Setting Die: Sets the pin into the material with controlled pressure.
• Hole Cutter: Prepares a hole only when the real material and pin structure require it.
• Press: Supplies stable pressure to the matched setting die.

Do not use this product as a Hole Cutter. It does not make a hole in leather, fabric, cardboard, canvas or webbing.

Suitable Applications

• Leather bags, wallets and card holders
• Belts, straps, webbing and accessory details
• Leather cases, pouches and organisers
• Garment, hat, vest and jacket hardware details
• Decorative sheet metal accessory applications
• Sample making, repair work and small-batch workshop production

Press and Connection Compatibility

Use this die with a physically compatible hand tool, manual hand press, impact press, electric machine or pneumatic machine. For repeat applications, a Manual Hand Press can provide more consistent pressure after connection compatibility is confirmed.

M6 and 1/4 in are different thread standards. Confirm the actual die holder, thread diameter, thread pitch and press alignment before use. Similar thread diameter does not guarantee safe mechanical compatibility.

Material Preparation

Pre-punching is not required in every application. Thin leather, flexible textiles and softer materials may permit direct installation with a matched die and controlled pressure.

For thick leather, rigid cardboard, coated fabric, dense canvas, webbing or multilayer materials, sample-test the actual production stack. When preparation is needed, choose the Hole Cutter according to the real pin structure and material behaviour, not from the 4 mm / 0.16 in inner diameter alone.

Correct Application Sequence

1. Check material thickness, hardness and total layer count.
2. Select the compatible sheet metal Suzan Pin with a 4 mm / 0.16 in inner diameter and 6.5 mm / 0.26 in barrel height.
3. Mark the exact installation position.
4. Test whether material preparation is required.
5. Place the pin in the correct application direction.
6. Fit the Suzan Pin Setting Die into compatible equipment.
7. Apply centred and controlled pressure.
8. Inspect the visible surface, barrel closure and holding result.

Frequently Asked Questions

What pin is this die designed for?

It is designed for compatible sheet metal Suzan Pins with a 4 mm / 0.16 in inner diameter and a 6.5 mm / 0.26 in barrel height.

Does this die punch the material?

No. This is a setting die only. Use a separate Hole Cutter where material preparation is required.

Can it be used with every 4 mm pin?

No. The full pin geometry, barrel height, reverse-side closure form and setting surfaces must be compatible.

Why is the 6.5 mm barrel height important?

The barrel height must suit the total thickness of the material stack so the pin can close correctly without excessive deformation or insufficient holding.

Can it be used with a manual hand press?

Yes, after the die holder, thread standard and press alignment have been physically confirmed.

Is pre-punching always necessary?

No. The need depends on material thickness, hardness, layer count and the actual pin structure.

Are the pins and press included?

No. This product includes the setting die only. Pins, presses, adapters and Hole Cutters are separate items.